Features & Devices

Inverter ❽

The TRIPP-LITE PowerVerter DC/AC power inverter allows you to charge your devices using a normal AC plug you'd use in a wall outlet or via USB.

To use, plug the inverter into your vehicle's cigarette lighter outlet while the vehicle is running, and ensure that the red switch is flipped on and the front and rear ventilation fans are unobstructed.

The AC outlet will be the primary charging port for the RL4e Label Printer. The USB ports can be used to charge your handheld devices; the 2.1A port will charger faster than the 1A.

If your inverter sounds an alarm:

Turn the inverter OFF when not powered by a running vehicle.
If alarm continues, consult inverter manual.

Paper Printer ❺

The printer is a compact, portable EPSON WF-100, chargeable via AC (faster) or USB (slower).

Printer parts:

Figure A

Micro USB port
Power inlet
Rear paper feed
Edge guide
Printer cover
Control panel
Output slot
Power light
Battery charging light

Figure B

Inner cover
Ink cartridge holder (do not remove)

Figure A

Figure B

Printing:

First, follow the charging and connection instructions.

Open the printer by sliding the silver tab on the front upwards, and unfold the front and top panels.

Turn on (or off) by pressing the power button on the left side of the control panel (#6 in Fig. A). The power light's on/off status reflects the power status of the printer. (#8 in Fig. A)

Loading paper:

Slide the edge guide (#4 in Fig. A) to the far left. Insert paper in the rear paper feed (#3 in Fig. A), with the print side facing up. Slide the edge guide right so it gently holds the paper in place. Select the size and type of paper you just loaded on the product LCD screen.

Note: Do not load more than 20 sheets of plain paper, or 1 envelope at a time.

This printer should accept any of the following media types, barring any quality changes by the manufacturers:

Single-sheets

Size:

A4 (8.3 × 11.7 inches [210 × 297 mm])
Letter (8.5 × 11 inches [216 × 279 mm])
Legal (8.5 × 14 inches [216 × 357 mm])
A6 (4.1 × 5.8 inches [105 × 148 mm])
3.5 × 5 inches (89 × 127 mm)
4 × 6 inches (102 × 152 mm)
5 × 7 inches (127 × 178 mm)
8 × 10 inches (203 × 254 mm)

Paper types: Plain paper and paper distributed by Epson

Weight: 17 lb (64 g/m2 ) to 24 lb (90 g/m2 )

Envelopes

Size:

No. 10 (4.1 × 9.5 inches [105 × 241 mm])

Paper types: Plain bond paper

Weight: 20 lb (75 g/m2 ) to 24 lb (90 g/m2 )

RL4e Label Printer ❹

The label printer is thermal printer capable of printing labels on demand, on the go.

Printer parts:

A. Thumb Latch

B. Lid

C. Supply Hubs

D. Media

Printing:

First, follow the charging and connection instructions.

Turn on or enter sleep mode by tapping the Power button in Fig. 3.

Turn off by pressing and holding the Power button for 4 seconds.

Loading media:

Slide the orange thumb latch rearward and then lift up on the lid. (Fig. 1)
Slide and hold open the two orange supply hubs. Orient the label roll as shown in Fig. 1, insert it into the printer, and allow the hubs to retract, grabbing the cardboard core. Close the cover and press the "Paper Feed" button to allow the printer to align the media within. The printer should advance to the start of the next label, ready to print.

Figure 1

Figure 2

Figure 3

Figure 4

Backup Battery Pack ❼

Provides backup mobile power source for laptop when not in vehicle
To enable AC power from the Battery Pack, press and hold the power button on the bottom
When light by plug is green, AC is on
The prevent draining the battery when not in use, press and hold the power button until green light turns off

USB Hub ❾

The USB hub interconnects power power and data for the electronics devices, and allows your laptop to communicate with the printer. It is powered via the Inverter through the barrel type plug, and the top square connector is connected via a USB cable along the Laptop Arm to your laptop.

Page updated

Report abuse